Topology optimization in lightweight design of a 3D-printed flapping-wing micro aerial vehicle

Topology optimization is an effective method to obtain a lightweight structure that meets the requirements of structural strength. Whether the optimization results meet the actual needs mainly depends on the accuracy of the material properties and the boundary conditions, especially for a tiny Flapping-wing Micro Aerial Vehicle (FMAV) transmission system manufactured by 3D printing. In this paper, experimental and numerical computation efforts were undertaken to gain a reliable topology optimization method for the bottom of the transmission system. First, the constitutive behavior of the ultraviolet (UV) curable resin used in fabrication was evaluated. Second, a numerical computation model describing further verified via experiments. Topology optimization modeling considering nonlinear factors, e.g. contact, friction and collision, was presented, and the optimization results were verified by both dynamic simulation and experiments. Finally, detailed discussions on different load cases and constraints were presented to clarify their effect on the optimization. Our methods and results presented in this paper may shed light on the lightweight design of a FMAV.     

过氧化氢/紫外线/臭氧氧化技术处理肼类污水的应用

采用放大试验规模（处理量1 m³/h）的H₂O₂（过氧化氢）/UV（紫外线）/O₃（臭氧）氧化技术处理肼类推进剂污水，在30.0±1.6 ℃，pH=9.0±0.2的条件下，研究肼类的过氧化氢增强光解臭氧化降解。对比不同氧化技术的协同效应以及对污水降解的影响，重点考察过氧化氢、紫外线、臭氧和初始浓度等工艺参数对降解效果的影响，对氧化技术的应用进行了优化。研究结果表明：该技术可使COD去除率提高27.66%，肼类的降解速率随着过氧化氢投加量、紫外线辐射强度、O₃投加速率和水质地提高而升高，随着初始质量浓度的提高而下降。在最佳工艺下，处理5 000 mg/L质量浓度的废水，处理60 min时，COD去除率分别为98.62%（偏二甲肼）、99.17%（甲基肼）、99.94%（肼）和93.25%（单推-3）。     

双模块下颌式内转进气道/圆锥前体一体化布局研究

为实现三维内转进气道的内收缩流场与圆锥前体的外压缩流场的良好匹配，提出了一种双模块下颌式内转进气道/圆锥前体(Double-modules Chin Inward-turning Inlet and Conical Forebody，DCII/CF)一体化设计方法，获得一种新颖的双发并置、侧向安装的DCII/CF一体化布局。针对该布局形式，开展了DCII/CF一体化构型与传统的单模块内转进气道/圆锥前体(Single-module Inward-turning Inlet and Conical Forebody，SII/CF)一体化构型的数值对比研究。结果表明：DCII/CF一体化布局不仅为内转进气道提供了优秀的前体附面层排移效果，还有效避免了传统SII/CF布局中前体附面层与进气道内部流场之间的相互干扰。在Ma∞=6.0设计状态，DCII/CF一体化布局的进气道总压恢复系数相较传统的SII/CF布局有了显著提高，从0.403提高至0.482；但由于前体附面层的排移，该布局的捕获流量略有降低， SII/CF的流量系数为0.956，该布局则为0.917。而在非设计状态，该布局形式同样具备较好的总压恢复性能，在Ma∞=5.0与Ma∞=4.0的总压恢复系数分别达到了0.586和0.682，明显高于SII/CF的总压恢复系数0.507和0.619。     

在二元柔壁自适应风洞中利用面元法进行三元模型实验

简要叙述了在西北工业大学二元柔壁自适应风洞中利用面元法进行二元半机翼模型试验的研究情况，分析了面元法的基本思想和部分试验结果。     

某型制导雷达部分元器件失效模式的分析

对某型号制导雷达部分元器件进行了失效分析，找出了导致元器件失效的原因，指出设计是提高可靠性的关键，并根据有关元器件情况对生产方与使用方提出了建议。着重讨论了设计师应注意的问题和应该遵循的设计原则。针对失效情况，提出了一些具体的设计构想。     

表贴式永磁电机的两种充磁方式

研究了表贴式永磁电机的两种充磁方式。首先利用已有文献电机参数验证了有限元模型的正确性,对比分析了两种充磁方式下电机磁密和磁钢磁势的分布特点,研究表明内转子结构平行充磁方式具有提供更大的气隙磁通潜力,而外转子结构则相反。接着研究了两种充磁方式,不同气隙下气隙总磁通随极对数和磁钢厚度的变化规律。同时明确了两种充磁方式各自使用场合,给出了最佳磁钢厚度的取值范围。本文工作有助于正确选择表贴式永磁电机的充磁方式和磁钢厚度,以发挥磁钢潜力,改善电机性能。     

虚拟环境系统中复杂模型的建立--3D资源在快速开发虚拟环境系统中的应用

对利用3D资源在快速开发虚拟环境系统中的方法进行了研究。在开发虚拟环境系统的过程中，复杂模型的建立是必不可少的，仅仅利用OpenGL函数编程来实现仿真是很困难的，针对该问题提出了利用3D资源进行3D文件读取和转换的两种方案，分析了虚拟环境中复杂模型的建立以及处理的基本方法，并对数控车床的仿真进行了详细介绍。     

考虑胶层蠕变行为的胶接结构有限元分析

本文考虑胶层材料的蠕变行为，采用模拟岩层纹理单元的有限元法，分析工程中使用的典型胶接结构的应力场和位移场。数值结果表明，胶层蠕变行为对胶接结构位移和应力场均有较大影响     

Global Response of Martian Plasma Environment to an Interplanetary Structure: From Ena and Plasma Observations at Mars

As a part of the global plasma environment study of Mars and its response to the solar wind, we have analyzed a peculiar case of the subsolar energetic neutral atom (ENA) jet observed on June 7, 2004 by the Neutral Particle Detector (NPD) on board the Mars Express satellite. The “subsolar ENA jet” is generated by the interaction between the solar wind and the Martian exosphere, and is one of the most intense sources of ENA flux observed in the vicinity of Mars. On June 7, 2004 (orbit 485 of Mars Express), the NPD observed a very intense subsolar ENA jet, which then abruptly decreased within ∼10 sec followed by quasi-periodic (∼1 min) flux variations. Simultaneously, the plasma sensors detected a solar wind structure, which was most likely an interplanetary shock surface. The abrupt decrease of the ENA flux and the quasi-periodic flux variations can be understood in the framework of the global response of the Martian plasma obstacle to the interplanetary shock. The generation region of the subsolar ENA jet was pushed towards the planet by the interplanetary shock; and therefore, Mars Express went out of the ENA jet region. Associated global vibrations of the Martian plasma obstacle may have been the cause of the quasi-periodic flux variations of the ENA flux at the spacecraft location.     

精密机械零件的统计尺寸公差

精密机械产品的发展要求具有高性能、高可靠性和高质量。如果用设计时减小公关的方法来保证精度，则将难以解决加工和装配中产生的问题。因此需要在采用尽可能大的公差值的民政部下满足精度一文将讨论一些实例，寻找借助于统计尺寸公差降低加工精度要求的办法。